sw94-2Two distinct washer configurations are integrated in this single stamping to provide two distinct load and deflection stages. The vertical “wall” that results from the forming of this washer is greater that the material thickness in height. This is a load bearing wall that changes the inside-outside radius relationship of the two washer configurations and significantly increases total load-to-flatten capability. The Square Cone (Square Dome) washer provides greater spring return and tension at minimum torque tolerances and has the strength to support maximum torque loading.

Tests have shown that a Square Cone (Square Dome) washer will achieve the same clamp load as a standard conical washer at 30% less torque. In most applications, applied torque is used as a method of determining whether adequate clamp load has been developed in a joint. The Square Cone (Square Dome) washer provides maximum uniformity in the torque to tension ratio. With its large deflection range, the Square Cone (Square Dome) washer allows torque to develop gradually, eliminating the shock loading that causes installers to develop carpel tunnel syndrome.

Inch Parts

Hole
Size
Inside Diameter
Min.
Inside Diameter
Max.
Outside Diameter
Min.
Outside Diameter
Max.
Free Height
Min.
Free Height
Max.
Thickness ITW Product Number WCL Product Number
4 0.116 0.123 0.244 0.25 0.025 0.048 0.015 3204-04-01 SQC-0112-04-01
6 0.142 0.15 0.307 0.32 0.039 0.061 0.025 3206-05-02 SQC-0138-05-02
6 0.142 0.15 0.433 0.446 0.05 0.073 0.025 3206-07-01 SQC-0138-07-01
8 0.168 0.176 0.37 0.383 0.05 0.073 0.03 3208-06-01 SQC-0164-06-01
8 0.168 0.176 0.495 0.508 0.062 0.064 0.032 3208-08-01 SQC-0164-08-01
10 0.195 0.204 0.433 0.446 0.054 0.078 0.032 3210-07-01 SQC-0190-07-01
1/4 0.256 0.267 0.74 0.76 0.1 0.131 0.055 3214-12-01 SQC-0250-12-01
3/8 0.366 0.372 0.768 0.787 0.717 0.195 0.109 3221-14-01 SQC-0375-14-02
3/8 0.394 0.409 0.865 0.885 0.169 0.199 0.109 3220-14-02 SQC-0500-20-03
1/2 0.512 0.526 1.24 1.26 0.235 0.267 0.15 3224-20-03 SQC-0500-20-03

Metric Parts

Hole
Size
Inside Diameter
Min.
Inside Diameter
Max.
Outside Diameter
Min.
Outside Diameter
Max.
Free Height
Min.
Free Height
Max.
Thickness ITW Product Number WCL Product Number
M3 3.61 3.81 7.8 8.13 0.99 1.55 0.64 3206-05-02* SQC-0138-05-02
M4 4.27 4.47 9.4 9.73 1.27 1.85 0.76 3208-06-01* SQC-0164-06-01
M5 4.95 5.18 11 11.32 1.33 1.96 0.81 3210-07-01* SQC-0190-07-01
M6 6.4 6.78 18.8 19.3 2.54 3.33 1.4 3214-12-01* SQC-0250-12-01
M10 9.75 10.011 22.04 22.48 3.71 4.47 2.36 3220-14-03* SQC-0375-14-03